一本一道久久综合狠狠老,欧美孕妇xxxx做受欧美88,亚洲精品国产美女久久久99

丁基膠涂布機常見故障解決方式

時間：2023-04-24 來源：http://m.bjrcc.com.cn/ 發布人：昌盛機械

丁基膠涂布機出現故障，可能會導致整個中空玻璃的進程停滯。而丁基膠涂布機是相對簡單的中空玻璃設備，康捷機械為您介紹一下丁基膠涂布機的常見故障，以及遇到類似故障處理的方法。

If the butyl adhesive coating machine malfunctions, it may cause the entire process of insulating glass to stall. The butyl adhesive coating machine is a relatively simple insulating glass equipment. Kangjie Machinery will introduce you to the common faults of the butyl adhesive coating machine and the methods for handling similar faults.

1.丁基膠涂布機擠出的丁基膠是毛刺不光滑時，如果是新設備，應先觀察出膠孔是否光滑，如果出膠孔粗糙，應先打磨，再試機器；舊機器，可能顯示的溫度與實際的不相符，這時就需要將溫度進行上調，直到出膠正常即可；

1. When the butyl adhesive extruded by the butyl adhesive coating machine has uneven burrs, if it is a new equipment, it is necessary to first observe whether the adhesive hole is smooth. If the adhesive hole is rough, it should be polished first and then the machine should be tried again; Old machines may display temperatures that do not match the actual ones, so it is necessary to increase the temperature until the glue is released normally;

2.丁基膠涂布機打出的膠粘不到鋁隔條上時，可能是原因還是溫度過低，與膠要求的溫度不太符合，只需要咨詢丁基膠提供方需要的溫度，將溫度調整合適即可；
臥式丁基膠涂布機

2. When the adhesive produced by the butyl adhesive coating machine cannot adhere to the aluminum spacer strip, the most likely reason is that the temperature is too low, which does not meet the required temperature for the adhesive. Simply consult the butyl adhesive supplier for the required temperature and adjust the temperature appropriately;

3.丁基膠涂布機出現膠頭漏膠，膠頭下面是硅膠墊，估計是硅膠墊損壞導致的，只需要更換硅膠墊即可，但是，需要提醒的是，擠膠壓力過大才是導致硅膠墊損壞的根本原因，不建議將擠膠壓力調的過大；

3. The butyl adhesive coating machine has adhesive leakage at the adhesive head, and there is a silicone pad underneath the adhesive head. It is estimated that the silicone pad is damaged, and only the silicone pad needs to be replaced. However, it should be noted that excessive extrusion pressure is the root cause of the damage to the silicone pad, and it is not recommended to adjust the extrusion pressure too high;

4.丁基膠涂布機的膠頭或膠缸不加熱，估計是加熱棒損壞，更換即可；

4. If the rubber head or cylinder of the butyl adhesive coating machine is not heated, it is estimated that the heating rod is damaged and can be replaced;

5.丁基膠涂布機的傳送皮帶跑偏，這個應該算不得故障，只需要調整四個角的皮帶輪即可；

5. The conveyor belt of the butyl adhesive coating machine deviates, which should not be considered a fault. It only needs to adjust the belt pulleys at the four corners;

6.丁基膠涂布機的顯示屏不亮，可以正常使用。這可能是顯示屏損壞或者顯示屏供電線出現問題，更換即可；

The display screen of the butyl adhesive coating machine is not lit and can be used normally. This may be due to damage to the display screen or a problem with the power supply line of the display screen, replacement is sufficient;

本文由臥式丁基膠涂布機提供幫助，更多的相關內容請點擊http://m.bjrcc.com.cn 希望本文能夠為您帶來幫助，感謝您的閱讀！

This article is provided by a horizontal butyl adhesive coating machine for assistance. For more related content, please click on http://m.bjrcc.com.cn I hope this article can be helpful to you. Thank you for reading!

上一篇：丁基膠打膠機主要部件怎么保養？ 下一篇：全自動中空玻璃生產線生產及各部件要求

相關新聞 more+