中空玻璃打膠機不出膠的原因及解決方法：
Reasons and solutions for failure of insulating glass gluing machine:
1、檢查氣源是否在0.6～0.8Mpa之間；
1. Check whether the air source is between 0.6 and 0.8MPa;
2、在觸摸屏的編輯功能菜單中檢查印章是否未使用；
2. Check whether the seal is not used in the editing function menu of the touch screen;
3、檢查氣動開關是否被擋住；
3. Check whether the pneumatic switch is blocked;
4、檢查黑膠氣動開關和電磁閥動作是否正常；
4. Check whether the black glue pneumatic switch and solenoid valve operate normally;
5、檢查比例泵上的智能壓力表是否報警，范圍7-35Mpa；
5. Check whether the intelligent pressure gauge on the proportional pump gives an alarm, with the range of 7-35mpa;
6、檢查液壓站內是否有壓力，若無壓力：
6. Check whether there is pressure in the hydraulic station. If there is no pressure:
1）清洗比例溢流閥
1) Cleaning proportional overflow valve
2）檢查比例控制器是否通電或松動；
2) Check whether the proportional controller is powered on or loose;
7、清洗時白膠是否可以釋放，如果不能，檢查313軟管和旋轉接頭是否堵塞；
7. Whether the white glue can be released during cleaning. If not, check whether 313 hose and rotary joint are blocked;
8、檢查一組比例泵下限傳感器IB233是否有信號，檢查二組比例泵是否有信號；
8. Check whether there is a signal from the lower limit sensor ib233 of the first group of proportional pumps and whether there is a signal from the second group of proportional pumps;
9、手動檢查中空玻璃打膠機的掃描數值是否正常。
9. Manually check whether the scanning value of insulating glass gluing machine is normal.
當雙組份膠在混合過程中發生局部固化時，打膠機打出來的膠就會出現結皮或硫化現象。出現這一現象的原因主要有三種：
When the two-component rubber is partially cured in the mixing process, the rubber produced by the beater will appear skinning or vulcanization. There are three main reasons for this phenomenon:

⑴膠體顏色較黑，固化快時，可能是由于B組分比例過高，過多的催化劑促使固化速度更快。此時，需要適當降低B組分的比例，將結皮或硫化膠沖洗干凈后施工；
(1) when the colloid color is black and the curing speed is fast, it may be due to the high proportion of component B and too much catalyst. At this time, it is necessary to properly reduce the proportion of component B and wash the crust or vulcanizate before construction;
⑵打膠機若打膠過程中伴有出膠慢的現象時，可能是混合芯長時間未清洗或清洗不完全，膠體結皮堵塞管道。因此，定期清洗靜態混合器是很有必要的。
(2) if the gluing machine is accompanied by slow glue output during gluing, it may be that the mixing core has not been cleaned for a long time or is not completely cleaned, and the colloid crust blocks the pipeline. Therefore, it is necessary to clean the static mixer regularly.
⑶當固化和出膠速度均無異常，而打出的膠仍有結皮或硫化現象時，則可能是設備停機時間較長，膠槍未清洗或洗槍不夠干凈，需要將結皮或硫化膠沖洗干凈后后施工。
(3) when there is no abnormality in the curing and glue outlet speed, but there is still peeling or vulcanization of the punched glue, it may be that the equipment has been shut down for a long time, the glue gun is not cleaned or the cleaning gun is not clean enough. It is necessary to wash the peeling or vulcanization before construction.
以上就是為大家介紹的有關雙組份打膠機的詳細介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務http://m.bjrcc.com.cn
The above is a detailed introduction to the two-component gluing machine. I hope it will be helpful to you If you have any questions, please contact us We will provide you with professional service http://m.bjrcc.com.cn