1、盡量避免把皮膚暴露在外

1. Try to avoid exposing the skin

熱熔膠機通上電后，會形成高壓電，觸電的危險性大家都知道，所以當熱熔膠在工作時，不要用皮膚去觸摸熱熔膠機的接線處與線路板，防止高壓電人事故發生。

After the hot melt adhesive machine is powered on, high voltage electricity will be formed, and the risk of electric shock is well known. Therefore, when the hot melt adhesive is working, do not touch the wiring and circuit board of the hot melt adhesive machine with your skin to prevent high voltage electric accidents.

2、熱熔膠機的保護面板不要隨意拆卸

2. Do not disassemble the protective panel of the hot melt adhesive machine at will

沒有必要，盡量不要拆卸熱熔膠機的保護面板。在特殊情況下如果一定要拆，應該把電源斷掉，也不要用濕手去觸摸帶電部位，防止觸電。

It is not necessary. Try not to remove the protective panel of the hot melt adhesive machine. Under special circumstances, if it must be removed, the power supply should be cut off first, and do not touch the live part with wet hands to prevent electric shock.

3、接地線不要遺漏

3. Do not omit the grounding wire

熱熔膠點膠機在安裝的時候一定要選用比較可靠的接地線，好處是可以防止在雷電環境下出現電擊危險，這也很好的保障了企業的生產安全。

When installing the hot melt glue dispenser, we must select a more reliable grounding wire. The advantage is that it can prevent the risk of electric shock in the lightning environment, which also well ensures the production safety of the enterprise.

4、三相空氣開關一定要選用質量好的

4. The three-phase air switch must be of good quality

電力和溫度是熱熔膠點膠機的重要參數，為了達到企業生產質量的要求，一定要配備質量好的空氣開關，這樣才能保障和提高企業的生產效率。

Power and temperature are important parameters of hot melt glue dispenser. In order to meet the requirements of enterprise production quality, we must be equipped with high-quality air switch, so as to ensure and improve the production efficiency of the enterprise.

5、熱熔膠點膠機工作環境要遠離水源

5. The working environment of hot melt dispensing machine shall be far away from water source

同樣，熱熔膠點膠機遠離水源也是考慮到觸電危險，有很多安全事故的發生都是因?yàn)榻咏?，從而觸電傷人的。

Similarly, the hot melt glue dispenser is far away from the water source. Considering the risk of electric shock, many safety accidents occur because it is close to the water source, resulting in electric shock.

以上的精彩內容來自：濟南昌盛機械雙組份打膠機的介紹及分享，更多內容請繼續關注我們：http://m.bjrcc.com.cn

The above wonderful content comes from the introduction and sharing of Jinan Changsheng machinery two-component gluing machine. Please continue to pay attention to us for more content: http://m.bjrcc.com.cn